What to know about Daikin chillers
Daikin equipment should be identified by the name on the actual chiller and the full model information, not merely by a building inventory. Some sites also have older McQuay-labeled equipment; send the label that is present rather than guessing at a replacement designation.
A chiller labeled Daikin in Lorain may be surplus after a plant upgrade, building closure or cooling-system replacement. Identify the exact machine rather than the entire plant, and specify whether the starter or drive is part of the proposed purchase.
Plan the pickup at your Lorain site
Lorain is in Lorain County. For equipment in the city of Lorain, provide the full site address and the specific loading entrance, not simply Lorain County. If the machine is in an older plant, identify any floor penetrations, shared piping and restricted access around it. The same information is useful for an outdoor unit on a fenced pad.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Compare the machine and its electrical gear
Photograph the nameplate, controller, overall frame and any separate drive or starter included in the transaction. Include the actual refrigerant marking.
Read the manufacturer, complete model and serial number from the chiller itself. Record rated cooling capacity, voltage, phase and the refrigerant on the unit plate if visible. A separate starter or variable-frequency drive can have its own label and may sit in another room. Photograph both and say whether the cabinet is included; a picture of a building automation panel alone does not identify the chiller.
Condition is information, not a testing requirement
Explain whether the machine is complete, has been modified, or has an unknown service history. It is not necessary to run it for an initial review.
If components were removed for another project, identify which ones are missing and photograph the remaining assembly. A machine with an incomplete control cabinet is different from a complete machine with an inoperable display, and both can be discussed without a test.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Keep an occupied building operating
If the property remains occupied, tell the buyer which cooling services and access routes must remain available. A facility representative should establish the work boundaries before qualified personnel plan the actual disconnect and refrigerant recovery. We coordinate and pay for that work within the agreed purchase scope. The owner does not need to vent, drain or isolate the chiller to request a cash offer.
Protect equipment that stays behind
Give the unit dimensions and the narrowest clearance along its proposed exit, including any overhead piping that cannot be moved.
Mark the chiller to be sold and photograph nearby systems that must remain. The route may pass sensitive controls, an occupied area or active machinery. The buyer coordinates and covers agreed rigging, crane if needed, loading and freight; the site representative helps identify operating boundaries and access restrictions. Rigging professionals choose methods after assessing the equipment, lift points and building conditions.
List a group of assets accurately
If you offer several chillers, identify each machine and whether the offer applies to the group or individual units. List separately located starters, drives or controls and state whether they are included. We make a cash offer and pay upfront before pickup after acceptance. The agreed purchase documents should describe what the buyer removes and the associated recovery, rigging and freight work.
If the chiller is being replaced, tell us when it will actually be released and which plant services must remain live. A replacement schedule and a completed isolation are different things.
What to send for a useful first conversation
For a central plant, mark the chiller being offered in a wide photograph and identify the starter or drive if it is elsewhere. Provide the model, serial, tonnage and refrigerant if known. Describe connected systems that remain in service, the likely exit and the facility contact who can review isolation and access.
For a chiller labeled Daikin in Lorain, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
What if the refrigerant is unknown?
Tell us the refrigerant is unknown and share any original or later labels you can safely photograph. We consider all refrigerants. The buyer coordinates required recovery with qualified personnel; the owner should not open a circuit or release refrigerant to identify it.
