What to know about water-cooled chillers
A water-cooled chiller uses a water-side system to reject heat. At a central plant, the chiller can be tied to both chilled-water and condenser-water piping, with pumps and a cooling tower elsewhere. A sale should specify which of these items are included and which remain with the building.
For a Cleveland water-cooled unit, clarify whether both water circuits remain connected and whether the starter is in the same room. Photographs of the vessels, connection points, floor and service exit help frame the work. The buyer handles the agreed disconnect and removal; the owner should not drain or cut the system to obtain an offer.
Plan the pickup at your Cleveland site
Cleveland is in Cuyahoga County. For a Cleveland mechanical room, describe whether the route leaves through a basement, a service corridor, a roof opening, or a ground-level door. A water-cooled unit can have separate condenser-water piping, so a simple exterior photo is not enough to establish the lift plan. Explain any building access or neighboring-tenant restrictions.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Inventory multiple machines separately
Photograph the chiller label, both ends of the vessels, control panel and visible water connections. Give the rated tons and refrigerant if listed.
When a plant has several chillers, use the physical position or site asset number to match each wide photo to its own nameplate. List manufacturer, model, serial, capacity, voltage and refrigerant for each unit where known. Similar cabinets can conceal different equipment or service histories. Specify whether the offer should cover one machine, a selected group or all of the machines identified.
Condition is information, not a testing requirement
Tell us if the machine is isolated, drained or still connected. Do not assume a water-cooled unit is empty because it is not running.
A prior refrigerant conversion, controller replacement or major repair can change how the machine is identified. An original plate and later service label can both be useful; include the dates or records only if available.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Confirm electrical and controls boundaries
A chiller can have power and control connections in different places, including a separate starter or drive. Tell the buyer where those cabinets are and which building controls remain. The buyer covers the agreed disconnects and refrigerant recovery, using appropriately qualified personnel. Do not remove covers, disconnect wiring, reset controls or assume that a blank display means the system is electrically safe.
Evaluate an outdoor lift and staging area
The removal plan must account for the two water circuits, any separate starter, room openings and the size and weight of each intended lift.
A pad or rooftop location is not enough information to select a crane. Show the unit and its surroundings, possible staging area, overhead obstructions and access for a truck. The buyer coordinates and covers agreed crane work when needed, rigging, loading, freight and hauling. Actual reach, ground support, clearance and equipment weight must be evaluated by the crew rather than estimated from cooling tons.
Understand what an offer covers
The offer considers the identifiable equipment and the work needed for the agreed removal. We make a cash offer and, when it is accepted, pay upfront before pickup. Confirm the amount, payment method, included components and buyer-paid removal scope in the transaction documents. Do not assume a separate pump, control cabinet or other nearby asset transfers unless it is specifically listed.
If a drive, starter or controller sits in another room, describe it separately and establish whether it is included. An offer is clearer when both the machine and its associated accessories are specifically listed.
What to send for a useful first conversation
Start with an asset list: manufacturer, model, serial, rated capacity, refrigerant and the location of each machine. Identify which units are surplus and whether they are still connected. Add photographs showing the room, pad or roof and the route toward a loading area. If the records are incomplete, mark unknown items rather than guessing or starting the machine.
For water-cooled chillers to sell in Cleveland, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
Can a non-running machine be sold?
Yes. We consider non-running and unknown-condition equipment, and do not require a performance test. Describe known defects and missing parts so an offer can reflect the machine as it sits. Site access and safe removal still need to be evaluated.
