What to know about York chillers
A York chiller offer depends on the actual machine, included accessories and access. A label on a building control system is not necessarily the label for the chiller itself. Identify the equipment being offered and distinguish it from other York-branded components at the site.
A chiller labeled York in Cleveland may be surplus after a plant upgrade, building closure or cooling-system replacement. Identify the exact machine rather than the entire plant, and specify whether the starter or drive is part of the proposed purchase.
Plan the pickup at your Cleveland site
Cleveland is in Cuyahoga County. For a Cleveland mechanical room, describe whether the route leaves through a basement, a service corridor, a roof opening, or a ground-level door. A water-cooled unit can have separate condenser-water piping, so a simple exterior photo is not enough to establish the lift plan. Explain any building access or neighboring-tenant restrictions.
Tell us about known site restrictions before scheduling. A site contact can explain what is accessible, but the removal team must evaluate the actual route, load and work area.
Separate cooling capacity from lifting weight
Send the machine model, serial number, tonnage and refrigerant from its own label, and photograph any matching external starter if it is included.
Cooling tons describe refrigeration capacity, not the number of tons a machine weighs. The total capacity of a complete chiller also may differ from the rating of one compressor or module. Provide the model and serial, rated unit capacity, voltage and refrigerant from the chiller label. If a manufacturer drawing provides operating or shipping weight, share the document and identify which weight it states.
Condition is information, not a testing requirement
Describe visible damage, missing components and the approximate last operating status if known. Unavailable history is acceptable and should be stated plainly.
A prior refrigerant conversion, controller replacement or major repair can change how the machine is identified. An original plate and later service label can both be useful; include the dates or records only if available.
We consider used, surplus and non-running chillers, including equipment of unknown operating condition. There is no need to restore power, repair a fault or perform a performance test to ask for a cash offer. Accurate disclosure and a possible site access review are different from requiring the machine to operate.
Keep an occupied building operating
If the property remains occupied, tell the buyer which cooling services and access routes must remain available. A facility representative should establish the work boundaries before qualified personnel plan the actual disconnect and refrigerant recovery. We coordinate and pay for that work within the agreed purchase scope. The owner does not need to vent, drain or isolate the chiller to request a cash offer.
Protect equipment that stays behind
Show the space between vessel ends, walls and other equipment, as well as the removal doorway, so the lifting approach is not based on an assumption.
Mark the chiller to be sold and photograph nearby systems that must remain. The route may pass sensitive controls, an occupied area or active machinery. The buyer coordinates and covers agreed rigging, crane if needed, loading and freight; the site representative helps identify operating boundaries and access restrictions. Rigging professionals choose methods after assessing the equipment, lift points and building conditions.
List a group of assets accurately
If you offer several chillers, identify each machine and whether the offer applies to the group or individual units. List separately located starters, drives or controls and state whether they are included. We make a cash offer and pay upfront before pickup after acceptance. The agreed purchase documents should describe what the buyer removes and the associated recovery, rigging and freight work.
For a closure, identify a primary contact who can provide access and answer questions after operations stop. Ask whether there are other contractors working in the same space or using the same loading area.
What to send for a useful first conversation
For a central plant, mark the chiller being offered in a wide photograph and identify the starter or drive if it is elsewhere. Provide the model, serial, tonnage and refrigerant if known. Describe connected systems that remain in service, the likely exit and the facility contact who can review isolation and access.
For a chiller labeled York in Cleveland, include the location and a contact who can confirm the asset and arrange site access. If a detail is unavailable, say so instead of taking an unsafe photograph or guessing at the specifications.
What if the refrigerant is unknown?
Tell us the refrigerant is unknown and share any original or later labels you can safely photograph. We consider all refrigerants. The buyer coordinates required recovery with qualified personnel; the owner should not open a circuit or release refrigerant to identify it.
